Showing posts with label 2N3055. Show all posts
Showing posts with label 2N3055. Show all posts

Monday, November 17, 2014

14W Class A Amplifier Circuit with 2N3055

14W Class A Amplifier Circuit with 2N3055

This class A amplifier circuit requires a preamp as it hasnt got much gain. Requires large heat sinks and a large transformer and a source of great power and wiring carefully, but the end is very simple and sounds great. The zener diode disclaims any wave from the power supply, but still just want a wave of 10mV max. The ripples reaching the entrance is amplified, so the zener get rid of that, but there is still dominated him to reach the power stage.

Many early amplifiers operated in Class A, but as 10W power output rose above the problems of heat dissipation and design of the power supply caused most manufacturers to turn to the simplest, arrangements more efficient class B and put up with the consequent decrease in the perceived quality of output. Why Class? Because, when biased in class A, the transistors are always on, always ready to respond instantly to an input signal. Class B and Class AB output stage requires a microsecond or more on. The kind of a cleaner operation allows operation under high voltage swing that occurs when the transient audio signal feed difficult loads. Your amplifier is basically simple, as shown in the block diagram.
Read More..
Posted by at
Labels: , , , , , ,

Monday, October 13, 2014

2N3055 Variable DC Power Supply circuit Diagram

Voltage range: 0.7 – 24V Current limiting range: 50mA – 2Ahttps://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhhSs-ctSHZs7rS9MyKfXgLuweJsfES8qhQbGRMBR7meu51qY2tqGMCUXbH54q_Y-Vu1DHaSzoMU500UVz7lgqDC8wTjB4eQ8OTZJzpJlXZC10iLZePDiJrJPGx3yTUFRKM0EPBnYFz6eU/s800/LM1458+and+2N3055+DC+Variable+Regulator+Power+Supply.gif

A Variable DC Power Supply is one of the most useful tools on the electronics hobbyist’s workbench. This circuit is not an absolute novelty, but it is simple, reliable, “rugged” and short-proof, featuring variable voltage up to 24V and variable current limiting up to 2A. Well suited to supply the circuits shown in this website. You can adapt it to your own requirements as explained in the notes below.
Notes:

* P1 sets the maximum output current you want to be delivered by the power supply at a given output voltage.
* P2 sets the output voltage and must be a logarithmic taper type, in order to obtain a more linear scale voltage indication.
* You can choose the Transformer on the grounds of maximum voltage and current output needed. Best choices are: 36, 40 or 48V center-tapped and 50, 75, 80 or 100VA.
* Capacitor C1 can be 2200 to 6800µF, 35 to 50V.
* Q4 must be mounted on a good heatsink in order to withstand sustained output short-circuit. In some cases the rear panel of the metal box in which you will enclose the circuit can do the job.
* The 2N3055 transistor (Q4) can be replaced with the slightly less powerful TIP3055 type.

Parts:
P1____________500R Linear Potentiometer
P2_____________10K Log. Potentiometer
R1,R2___________2K2 1/2W Resistors
R3____________330R 1/4W Resistor
R4____________150R 1/4W Resistor
R5______________1R 5W Resistor
C1___________3300µF 35V Electrolytic Capacitor (see Notes)
C2______________1µF 63V Polyester Capacitor
D1,D2________1N5402 200V 3A Diodes
D3_____________5mm. Red LED
Q1____________BC182 50V 100mA NPN Transistor
Q2____________BD139 80V 1.5A NPN Transistor
Q3____________BC212 50V 100mA PNP Transistor
Q4 __________2N3055 60V 15A NPN Transistor
T1_____________220V Primary, 36V Center-tapped Secondary
50VA Mains transformer (see Notes)
PL1____________Male Mains plug
SW1____________SPST Mains switch

Read More..
Posted by at
Labels: , , , , , , ,
Subscribe to: Posts (Atom)